Maxim公司的MAX5974系列是寬輸入電壓峰值電流模式正向PWM控制器,不需要光耦合器,MAX5974A/MAX5974C適用于通用的電信電壓輸入,而MAX5974B/ MAX5974D輸入電壓可低至10.5V.器件內部有1%的誤差放大器,100kHz到600kHz可編程頻率,可編程頻率抖動以降低EMI和采用擴頻工作,主要用在PoE" title="PoE">PoE IEEE® 802.3af/at標準的以太網供電設備,有源鉗位正向DC/DC轉換器" title="DC/DC轉換器">DC/DC轉換器,IP電話,無線接入節點和安監照相機等.本文介紹了MAX5974系列主要特性, MAX5974A/B方框圖, MAX5974C/D方框圖以及典型應用電路圖,以及采用MAX5974A/B的12V/2A Class 4 PD參考設計主要特性和電路圖.

The MAX5974_ provide control for wide-input-voltage, active-clamped, current-mode PWM, forward converters in Power-over-Ethernet (PoE) powered device (PD) applications.

The MAX5974A/MAX5974C are well-suited for universal or telecom input range, while the MAX5974B/ MAX5974D also accommodate low input voltage down to 10.5V.

The devices include several features to enhance supply efficiency. The AUX driver recycles magnetizing current instead of wasting it in a dissipative clamp circuit.

Programmable dead time between the AUX and main driver allows for zero-voltage switching (ZVS). Under lightload conditions, the devices reduce the switching frequency(frequency foldback) to reduce switching losses.

The MAX5974A/MAX5974B feature unique circuitry to achieve output regulation without using an optocoupler, while the MAX5974C/MAX5974D utilize the traditional optocoupler feedback method. An internal error amplifier with a 1% reference is very useful in nonisolated design, eliminating the need for an external shunt regulator.

The devices feature a unique feed-forward maximum duty-cycle clamp that makes the maximum clamp voltage during transient conditions independent of the line voltage, allowing the use of a power MOSFET with lower breakdown voltage. The programmable frequency dithering feature provides low-EMI, spread-spectrum operation.

The MAX5974_ are available in 16-pin TQFN-EP packages and are rated for operation over the -40℃ to +85℃ temperature range.

MAX5974系列主要特性:

Peak Current-Mode Control, Active-Clamped Forward PWM Controller

Regulation Without Optocoupler (MAX5974A/ MAX5974B)

Internal 1% Error Amplifier

100kHz to 600kHz Programmable Q8% Switching Frequency, Synchronization Up to 1.2MHz

Programmable Frequency Dithering for Low-EMI, Spread-Spectrum Operation

Programmable Dead Time, PWM Soft-Start, Current Slope Compensation

Programmable Feed-Forward Maximum Duty- Cycle Clamp, 80% Maximum Limit

Frequency Foldback for High-Efficiency Light- Load Operation

Internal Bootstrap UVLO with Large Hysteresis

100μA (typ) Startup Supply Current

Fast Cycle-by-Cycle Peak Current-Limit, 35ns Typical Propagation Delay

115ns Current-Sense Internal Leading-Edge Blanking

Output Short-Circuit Protection with Hiccup Mode

Reverse Current Limit to Prevent Transformer Saturation Due to Reverse Current

3mm x 3mm, Lead-Free, 16-Pin TQFN-EP

MAX5974A/MAX5974C應用:

PoE IEEE® 802.3af/at Powered Devices

High-Power PD (Beyond the 802.3af/at Standard)

Active-Clamped Forward DC-DC Converters

IP Phones

Wireless Access Nodes

Security Cameras

圖1.MAX5974A/B方框圖

圖2.MAX5974C/D方框圖

圖3.MAX5974C/D典型應用電路圖

圖4.MAX5974A/B典型應用電路圖

圖5.MAX5974C/D典型應用電路圖

MAX5974A/B參考設計

This reference design is for a highly efficient, flyback, 12V/1A Class 2 powered device (PD) that is IEEE 802.3af/3at complaint and cost effective. The reference design can be customized to a 12V/2A Class 4 PD.

The design features the MAX5969B and MAX5974A. The MAX5969B controller is fully compliant with the IEEE 802.3af/at standard in a power-over-Ethernet (PoE) system.

The device can also get power from a wall adapter (WAD). The MAX5974A controls wide-input-voltage, active-clamped, inductive feedback, current-mode PWM converters and provides frequency foldback for PoE applications. Using these devices, this reference design is IEEE 802.3af/at compliant. It is also a high-performance, compact, and economical solution for a Class 3 PD or a Class 4 PD.

MAX5974A/B參考設計主要特性:

The 12V/1A PD meets the following specifications:

Input voltage: 36V to 57V

WAD input voltage: 36V to 57V (10V to 57V with a different transformer)

VOUT1: 12V/1A (up to 2A by optimizing the switching frequency)

Output ripple: ±2.5% (can be reduced by adding more output ceramic capacitors or disabling the frequency foldback, FFB)

Load transient VP-P: ±3% (25% step-load)

Line and load regulation: ±2%

Switching frequency: 300kHz (150kHz in FFB mode)

Total efficiency with a load of 2A at 3V and 48V input: 90.3%, including input LAN transformer and diode bridge (93.3%, not including input LAN transformer and diode bridge)
 
圖6.MAX5974A/B參考設計外形圖

圖7.MAX5974A/B參考設計電路圖
詳情請見:
http://datasheets.maxim-ic.com/en/ds/MAX5974A-MAX5974D.pdf
和
http://pdfserv.maxim-ic.com/en/an/AN4984.pdf